Most skillful workers by esefkarakas

Tom Stutz +5
Tom Stutz

I really like how he pulled all that dirt into the new boot.

14 күн бұрын
Amb
Amb

I tell you one damn thing he must be a good employee because he did that so freaking quick

11 күн бұрын
DJI mini 2 +1
DJI mini 2

Great video 😎 I usually do that while it's still on the car 🤣 I cut it down the seam line with a stanley knife, then I use good quality superglue a bit at a time to glue it back together, usually takes less than 15 mins

16 күн бұрын
Krankie V
Krankie V

In the US, it's generally less expensive to buy an entire CV shaft assembly than it is to pay for the labor to replace a joint, so nobody really does this here.

11 күн бұрын
Rainman hott
Rainman hott

Как же легко он сбил гранату молотком и сохранил стопор 😁 идеальный вариант

11 күн бұрын
Absentimental 1
Absentimental 1

So skilled!

13 күн бұрын
Ruben Omar Irurzo Revilla
Ruben Omar Irurzo Revilla

You must push it half stroke or in tvOS case spin it to one full side let the air escape then put your second belt. Then when the shaft works the air and grase moves inside Of the CV joint boot and lubricates the entire assembly

10 күн бұрын
wayne p +4
wayne p

My cv ring clamp pliers have a floating stop above the jaws to limit the height of the crimp

16 күн бұрын
Chris R +6
Chris R

Hard to find a CV boot kit these days. Been a while since I've done one 😌

13 күн бұрын
Noor Zaidi Ahmad
Noor Zaidi Ahmad

Great job ...!

14 күн бұрын
Luis Padilla
Luis Padilla

Jaja igual hago yo con la tenaza 💪🇦🇷👌👍

10 күн бұрын
akiey +2
akiey

Good work,,but Not all shop can change only part, normally they change 1 set

14 күн бұрын
Stephen Mckee
Stephen Mckee

You really did a good job the only thing I have to say is you need to pack more grease in that boot before you close that up next time. You didn't put nowhere near enough grease. You supposed to pack that boot full. Close the small side with a clamp first then pack the boot good then pop it on. You will extend the life of the bearings in that CV shaft

15 күн бұрын
Валентина РУСЬ
Валентина РУСЬ

Молодец!

Күн бұрын
Georg Andexler Andexler +4
Georg Andexler Andexler

Good work!

18 күн бұрын
Rudy Padilla
Rudy Padilla

S L O W down the video Tell the guy he does get paid for his speed. He is setting a standard. That will always be expected of him ,!!!!!!

18 күн бұрын
Anatolii Yatsenko
Anatolii Yatsenko

Well he tightened the clamps in opposite direction from each other 🤷‍♂️, no pros out there

8 күн бұрын
gagagaga +16
gagagaga

"Most skillful worker" Shows mechanic doing the easiest job

15 күн бұрын
Kelsy Cunningham +9
Kelsy Cunningham

When you do 100 a day, you get good.

17 күн бұрын
Juancarlo Rodriguez
Juancarlo Rodriguez

Añosssss de no veer que alguien cambiara un cv joint eso nomás en Mexico se hacía en los usa no los consigues por ningún lado solo la flecha completa… saludos.

12 күн бұрын
ABDALAZIZ ALSABBAGH
ABDALAZIZ ALSABBAGH

My brothers they use to repair them cars at home because of the economic blocked 1990-2003 in Iraq one of them is a mathematics teacher and the 2nd one is officer at Iraqi army they mostly fix everything in the car.

15 күн бұрын
MWR TV +2
MWR TV

Nice way to save

18 күн бұрын
Alberto marino Adawe
Alberto marino Adawe

Nice tips

7 күн бұрын
dan ven
dan ven

I appreciate the effort but if the customer doesn't want to buy a new axle there's always decent reman axles available. If that inside boot cracks within the next year then you're doing that axle again for free.

15 күн бұрын
Simon A, Mancinas.
Simon A, Mancinas.

Would you trust this one on the highway at 100 mph🤔 at least they will not hear you coming around the corner.

17 күн бұрын
something to see +3
something to see

Awesome work

18 күн бұрын
Михаил Шумский +1
Михаил Шумский

Хомуты не правильно поставил,нужно по ходу движения

8 күн бұрын
NAVRET +35
NAVRET

Scotty Kilmer: “If it doesn’t go ‘clunka clunka’ it’s fine.”

15 күн бұрын
Charles Underwood
Charles Underwood

Hey Scotty ! I thought this was done good enough for my car. Put the playback speed at normal .

15 күн бұрын
Ed Swope +1
Ed Swope

Doing a car repair in 45 minutes, but then charging 3 hours for labor because that is what "the book says it takes" should be considered theft, fraud, scam or whatever. Besides, fast doesn't mean it's done right.

14 күн бұрын
Beverly Roemer +4
Beverly Roemer

Omg 😱 Me being so excited I finally got it off I would be the one to forget to the put the boot 👢 on.

15 күн бұрын
Mohaimin Ahmed +5
Mohaimin Ahmed

Pack the grease into the bearings my brother, it will last longer.

13 күн бұрын
Сергей Смирнов
Сергей Смирнов

Очень проф.,внутреннее отверстие пыльника на грязь,наружнее на смазку!!!

12 күн бұрын
андрей березняк +1
андрей березняк

Человек молния. Профи.

17 күн бұрын
Walter Brown +1
Walter Brown

Nice

15 күн бұрын
H H
H H

Fácil si quieren ahorrar dinero

13 күн бұрын
Rus Lan +1
Rus Lan

Вот это что за смазка я сколько трогал настоящий литол. Выбрасывал и покупал серый ШРУС .

14 күн бұрын
jeff dudte
jeff dudte

Wow saved 10 bucks

14 күн бұрын
E-Racer +2
E-Racer

I don’t understand why they took it off of the vehicle. you can do that with it on the vehicle and actually save quite a bit of time!

14 күн бұрын
Timothy Thomas
Timothy Thomas

Exactly

8 күн бұрын
Andrew Murphy +1
Andrew Murphy

Ok I did not knowthat could be changed. I always thought that you had to change the entire drive shaft.

15 күн бұрын
kid +1
kid

Usually cheaper to replace the whole shaft. Same labour to remove shaft

14 күн бұрын
михо lucky
михо lucky

Куй так! Стопорное кольцо лопнуло,изакусило,пришлось разбивать,а внутренность резать!

13 күн бұрын
Wayne Spencer
Wayne Spencer

That doesn't look like the highest quality cv joint ther were burn marks that look to have been caused when grinding the track

17 күн бұрын
Курмангазы Сарсенбаев
Курмангазы Сарсенбаев

Базар жок

9 күн бұрын
Nicco Visconti +1
Nicco Visconti

Skillfull? I dont think you know what that word means.

13 күн бұрын
Scale Modeling on the cheap
Scale Modeling on the cheap

And you wonder at constant parts failures. Make sure you dont clean anything

7 күн бұрын
borys104 +13
borys104

Wrong grease sulphur molybdenum need to use

16 күн бұрын
US
US

В хорошей гранате смазка заправляется на заводе

12 күн бұрын
Devin Walton +9
Devin Walton

Wrong grease? Doesnt look like the high MoS2 stuff.

17 күн бұрын
Adil Shaukat
Adil Shaukat

I think CV grease is recommended kindly correct me

11 күн бұрын
Chevy Big block
Chevy Big block

Agreed 🤙

14 күн бұрын
Victor Silvestre Coria
Victor Silvestre Coria

That is so simple here in tje philippines repairinf velocity sucks can you post more harder tjan that

15 күн бұрын
Alex
Alex

This is skillful? What is rebuilding an engine or transmission looks like

4 күн бұрын
R
R

Hahaha. Never seen anything butchered so bad…

12 күн бұрын
Khan Sajjad
Khan Sajjad

Great

16 күн бұрын
Michael Ruberton
Michael Ruberton

Wrong Grease should use black not lithium for the roller bearing, read a out hertzian contact points

15 күн бұрын
Daniel Nistoran
Daniel Nistoran

Greșit se bate în interior iar la burduf trebe scos un pic aerul din el pus colierele bine că altfel se sparge.

16 күн бұрын
Kellen
Kellen

they say he is still washing his hands

11 күн бұрын
John O' Mahony
John O' Mahony

The slightest bit of grease on the outer end & the boot slips off.

14 күн бұрын
Igor Rodin +1
Igor Rodin

Хомуты застёжками в одну сторону ставятся, по ходу движения. Смазка странная, не для шрусов.

12 күн бұрын
Igor Rodin
Igor Rodin

@Дмитрий Горчаков я тоже офигел.

11 күн бұрын
Дмитрий Горчаков
Дмитрий Горчаков

Бывает и такая смазка, только она для трипоида а не для шарикового. А то что он болгаркой хомуты пилит, тут походу никого не смущает?)

11 күн бұрын
White Dove
White Dove

Bravo, replace the old one with a new one in a perfect way.👍🌹👏

18 күн бұрын
Thomas Catford
Thomas Catford

Why speed up the video?

13 күн бұрын
Carlos GOMEZ LAURA
Carlos GOMEZ LAURA

Esmeril???? Para cortar los seguros,,,

7 күн бұрын
Namehere
Namehere

No grease in the boot before assembly? Fail.

13 күн бұрын
Rafael Moreno
Rafael Moreno

Bien cambio de puntas

2 күн бұрын
Edvaldo Nunes dos Santos
Edvaldo Nunes dos Santos

Legal

14 күн бұрын
David Elliott
David Elliott

Now try to buy a replacement inner joint. They are simply not available yet are the most likely to be run dry (out of fight out of mind).

13 күн бұрын
이청운 +1
이청운

등속죠인트가 수리가되는군요

16 күн бұрын
땡수
땡수

진짜 모르고 물어본거쥬?고무 부트만 찢어져도 수리는 가능 합니다만 손에 구리스 묻고 힘들고 시간이 더 거리고 이익이 안남으니 간편하게 비싼 순정부품으로 갈아버립니다.그나마 재생부품이 저렴해유.

15 күн бұрын
Gilbert Matson
Gilbert Matson

Why is it such a big deal . That's their job protect and serve the public.

12 күн бұрын
Александр Харитонов
Александр Харитонов

А в пыльник смазку?

3 күн бұрын
fuhk off
fuhk off

I'm calling bullshit. Just hitting that three times with a hammer, that ring never lets that thing come off that easy. You have to beat that end for hours to get the axle out of it, cuz those Rings always get screwed up from being driven for a long time.

14 күн бұрын
멍멍킹 +1
멍멍킹

아...이제 알겠네 재생품이 왜 빨리 망가지는지를..ㅅㅂ

11 күн бұрын
Dj GooF
Dj GooF

Мало смазки в шрус набил

14 күн бұрын
Pocket Sand +1
Pocket Sand

Lmao most skilled? He replaced a U joint.... my 5 year old Nephew could do this.

13 күн бұрын
Alva Felix
Alva Felix

Amazing because in north America they not gonna do that they just but a whole new one

3 күн бұрын
Victor Silvestre Coria
Victor Silvestre Coria

That not yet skill here mechanics here are great in fabricsting hard parts to make it work

15 күн бұрын
Los Lobos
Los Lobos

Say huh???

13 күн бұрын
Marc +3
Marc

I would just replace the whole cv.

15 күн бұрын
Techn' Moto +3
Techn' Moto

Cheaper to just replace the shaft

16 күн бұрын
Daniel Nistoran
Daniel Nistoran

Vaseline grafitata

16 күн бұрын
-Agent- 47-
-Agent- 47-

Those small pudgy hands are hilarious.... someone show a 6 year old kid to do this? 😆😆😆😆

17 күн бұрын
dswagg585 xbox 1
dswagg585 xbox 1

Sweet work but those little crimp ties keep your ball joint on???

18 күн бұрын
dswagg585 xbox 1
dswagg585 xbox 1

@mlevenha thank you ive never seen a system like that im not a mechanic either but I appreciate the respectful response thank you very much

18 күн бұрын
mlevenha +1
mlevenha

nah it's held on by that ring you see him install. It compresses when he slides the joint over and expands again locking the joint in place. the metal crimp things just hold the boot on lol

18 күн бұрын
Humberto Moncayo
Humberto Moncayo

No me parese una piesa muy segura

17 күн бұрын
coal1987
coal1987

Gloves!! Please!!

11 күн бұрын
Furhat Arziev
Furhat Arziev

Шрус пожалел

15 күн бұрын
Tour and Technical
Tour and Technical

एक्सेल का आगे वाला कहां मिलता है

15 күн бұрын
I am Survivor
I am Survivor

that's not for CV grease

10 күн бұрын

Келесі

Most Satisfying Factory Machines and Ingenious Tools

8:20

Most Satisfying Factory Machines and Ingenious Tools

Amused

Рет қаралды 66 МЛН

1908 Wine Corking Machine [Restoration]

29:19

1908 Wine Corking Machine [Restoration]

Hand Tool Rescue

Рет қаралды 436 М.

Қызыл Раушан

3:23

Қызыл Раушан

Ұланғасыр Қами - Topic

Рет қаралды 288 М.

Ingenious Construction Workers That Are On Another Level ▶31

9:11

Ingenious Construction Workers That Are On Another Level ▶31

Quantum Tech HD

Рет қаралды 8 МЛН

Jak Rosjanie mogą to tolerować?

10:58

Jak Rosjanie mogą to tolerować?

Viacheslav Zarutskii

Рет қаралды 248 М.

Satisfying Videos of Workers With Amazing Skills

9:01

Satisfying Videos of Workers With Amazing Skills

Quantum Tech HD

Рет қаралды 11 МЛН

Engine support from used tire

6:26

Engine support from used tire

Ryan tire's ideas

Рет қаралды 43 М.

The technique of peeling truck tire

10:29

The technique of peeling truck tire

Ban bekas & kerajinan

Рет қаралды 346 М.

TOYOTA OWNERS! Please NEVER Do THIS to Your Toyota!

48:12

TOYOTA OWNERS! Please NEVER Do THIS to Your Toyota!

The Car Care Nut

Рет қаралды 2 МЛН

Most Satisfying Factory Machines and Ingenious Tools!

8:58

Most Satisfying Factory Machines and Ingenious Tools!

CubeHub01

Рет қаралды 1 МЛН

Мальчики Стесняшки🤣

0:25

Мальчики Стесняшки🤣

edwardbil_pro

Рет қаралды 1,9 МЛН

#DAVA #ДАВА #Shorts #милана #миланахаметова

1:00

Tik-Tok: Алло подгузник ну, что как жизнь? (2021)

0:40

Tik-Tok: Алло подгузник ну, что как жизнь? (2021)

Екатерина Ковалева

Рет қаралды 809 М.

Хороший единорог vs плохой единорог!

25:21

Хороший единорог vs плохой единорог!

Трум Трум

Рет қаралды 69 М.

真似してみると・・・#shorts

0:13

真似してみると・・・#shorts

TEAM Coca-Cola_RedLinX[レッドリンクス]

Рет қаралды 1 МЛН